XYZ Carve Build Instructions
5.Main Mechanical BOM
Main Mechanical BOM
First check you have at least all the Mechanical bits in the Bill Of Materials (BOM) Below. You will likely have extras of a few parts, and also some hardware not listed here, that may not be needed unless particular options were ordered or upgrades are needed.
Main Mechanical BOM:
| Qty | Part | Image |
| 1 | Wide Makerslide X Axis |  |
| 1 | 2040 Drag Chain Support Extrusion |  |
| 1 | Makerslide Z Axis 200mm |  |
| 2 | Makerslide Y Axis 1000mm |  |
| 2 | 2020 Base (X axis length – 43mm) |  |
| 3 | 2020 Base (Y_Axis) |  |
| 2 | Gantry Side Plate |  |
| 1 | Z Motor Plate |  |
| 1 | Z Acme Lower Plate |  |
| 1 | Z Acme Plastic Shim |  |
| 1 | Spindle Mount Plate |  |
| 4 | Y End Plates |  |
| 6 | GT2 Belt Clamp |  |
| 2 | Drag Chain Support Bracket 1 |  |
| 2 | Drag Chain Support Bracket 2 |  |
| 1 | Drag Chain Support Bracket 3 |  |
| 1 | Extruded X Carriage |  |
| 1 | 65mm or 69mm Spindle Mount Front (Optional) |  |
| 1 | 65mm or 69mm Spindle Mount Back (Optional) |  |
| 10 | Spacer |  |
| 21 | Dual Bearing V Wheel |  |
| 6 | Dual Bearing Idler Pulley |  |
| 10 | Eccentric Nut |  |
| 4 | GT2 Pulley 1/4in Bore |  |
| 1 | GT2 Pulley 8mm Bore |  |
| 2 | F608-2RS Flanged Bearing |  |
| 1 | Z Acme Thread 232mm |  |
| 1 | GT2 Closed Loop Belt 80 Tooth |  |
| 1 | Z Acme Lead Nut Block |  |
| 10 | Grub Screw- M3x0.5 x 5 (Installed In Pulleys) |  |
| 4 | Socket Head Cap Screw – M5x0.8 x 10 |  |
| 8 | Socket Head Cap Screw – M5x0.8 x 16 | |
| 4 | Socket Head Cap Screw – M5x0.8 x 20 |  |
| 2 | Pan Head Machine Screw – M2x0.4 x 10 |  |
| 4 | Pan Head Machine Screw – M2x0.4 x 16 |  |
| 4 | Socket Button Head Cap Screw – M4 x 0.7 x 10 |  |
| 26 | Socket Button Head Cap Screw – M5 x 0.8 x 8 |  |
| 4 | Socket Button Head Cap Screw – M6 x 1 x 10 |  |
| 36 | Socket Button Head Cap Screw – M5 x 0.8 x 10 | |
| 20 | Socket Button Head Cap Screw – M5 x 0.8 x 12 |  |
| 4 | Socket Button Head Cap Screw – M5 x 0.8 x 20 |  |
| 19 | Socket Button Head Cap Screw – M5 x 0.8 x 25 |  |
| 8 | Socket Button Head Cap Screw – M5 x 0.8 x 35 |  |
| 2 | Socket Flat Countersunk Head Cap Screws – M5x35(2) |  |
| 8 | Socket Flat Countersunk Head Cap Screws – M4x10(2) |  |
| 54 | Tee Nuts Mix of Pre and Post Assembly |  |
| 4 | M2 Nut |  |
| 32 | M5 Washer |  |
| 10 | Prevailing Torque Hex Nut – M4 x 0.7 |  |
| 38 | Prevailing Torque Hex Nut – M5 x 0.8 |  |
| 4 | Nema 23 Stepper |  |
| 4 | Limit Switch (3 required, 1 spare) |  |
| 6 | 2020 Right Angle Gusset |  |
Was this helpful?
0 of 0 users found this section helpful